LAB MANUAL (Version 1.

0)
CCNA ROUTING & SWITCHING
(200-125)

From the Desk of Engr. Ahmed Saeed
Join Us on Facebook (My Cisco Center Group)
My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel
92-321-2418349

1

`

Copy Right

CCNA LAB MANUAL 200-125
Copyright @My Cisco Center
Published By

My Cisco Center, PECHS Block 6
Near Farhan hotel, Shahrah-e-Faisal Karachi.
Warning and Disclaimer,

This manual is designed to provide information about
CCNA (200-125). Every effort has been made to make this manual as
complete and accurate as possible, but no warranty of fitness is implied.
The information is provided on as basis and MCC shall have neither
liability nor responsibility to any person or entity with respect to any loss
or damage Arising from the information contained in this manual.
Authors
Engr. Fakhr Uddin Akbari
(Network Engineer)

My Cisco Center
Engr. Riaz Gul
(Network Engineer)
My Cisco Center
Reviewed and Approved By
Engr. Ahmed Saeed
Lead Cisco Trainer
My Cisco Center (MCC)
Engrahmed23@gmail.com
92-321-2418349
Join us on Facebook (My Cisco Center Group)
https://www.facebook.com/groups/pixcttc/
OR Visit us on our website
www.myciscocenter.com

From the Desk of Engr. Ahmed Saeed
Join Us on Facebook (My Cisco Center Group)
My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel
92-321-2418349

2

`

TABLE OF CONTENTS
Basic Configurations of Internetwork Operating System (IOS)
Configuring Telnet and SSH on Cisco Routers
Cisco Routers Password Recovery
Implementing Virtual Local Area Networks (VLANs)
Implementing VLAN Trunking Protocol Version 2 (VTP)
Implementing Port Based Security on Cisco Switches
Implementing IEEE (802.1d) STP and (802.1w) RSTP
Implementing Link Aggregation (Ether-Channel)
Implementing Inter-Vlan Routing using Router on a Stick
Configuring Static Route on Cisco Routers
Configuring Routing Information Protocol Version 2
Implementing Enhance Interior Gateway Routing Protocol (EIGRP)
Implementing Open Shortest Path First (OSPF) Version 2
Implementing IPv6 on Cisco Routers
Configuring IPV6 Stateless Auto Configuration
From the Desk of Engr. Ahmed Saeed
Join Us on Facebook (My Cisco Center Group)
My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel
92-321-2418349

3

Dynamic and PAT) Implementing Hot standby Routing Protocol (HSRP) Implementation of WAN Encapsulation TFTP Server FTP Configuring Syslog Server PPP Multilink GRE Tunnel From the Desk of Engr. Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349 4 .` Implementing RIPng on Cisco Routers Implementing Open Shortest Path First (OSPF) Version 3 Implementing EIGRP for IPV6 Networks Configuring DHCP on Cisco Routers Implementing Standard and Extended Access Control List (ACL) Implementing Network Address Translation (Static.

Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349 5 .0.2   In order to configure the Switch/Router.  Accessing Console of the Switch/Router      Modes of CLI  How to Set Hostname and Configure Console Password  How to Set Privilege level password  How to Set User Authentication in Switch TOPOLOGY   MCC-PC1 is directly connected to switch with IP address 10. accessing the console From the Desk of Engr.0.0.1   MCC-PC2 is directly connected to switch with IP address 10.0.` Basic Configurations of Internetwork Operating System (IOS) OBJECTIVE: Basic configurations of a Cisco Switch/Router.

 In packet tracer: From the Desk of Engr. Hyper Terminal is used to access the Command Line Interface (CLI) of the Device.`    RJ-45 to DB-9  adapter is used on the PC (COM port) to the device console Port through a rollover cable. Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349 6 .

Switch console: Modes of CLI: Switch> User-exec mode Switch# Privilege mode Switch(config)# Global Configuration mode From the Desk of Engr. Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349 7 . you will have Switch/Router Console.` Once you click OK.

`
How to switch in different modes:

Switch> enable
Switch# config terminal
Switch (config)#
NOTE: To return

to the previous mode use “Exit” command in the current mode .

How to Set Hostname and Configure Console Password:

Switch(config)# hostname MY_CISCO_CENTER
MY_CISCO_CENTER (config)#line console 0
MY_CISCO_CENTER (config-line)#password cisco123
MY_CISCO_CENTER (config-line)#login
How to Set Privilege level password:

!!! Clear Text Password not encrypted(less priority)
MY_CISCO_CENTER (config)#enable password ccna123
!!! Encrypted password (more Priority)
MY_CISCO_CENTER (config)#enable secret cttc123
Verify the Password:

MY_CISCO_CENTER (config)#exit
MY_CISCO_CENTER #exit
MY_CISCO_CENTER console 0 is now available
Press RETURN to get started.
User Access Verification
!!! TYPE
HERE
LINE
CONSOLE
Password Password:
MY_CISCO_CENTER >enable
!!! TYPE HERE Privilege Level Password
Password:

From the Desk of Engr. Ahmed Saeed
Join Us on Facebook (My Cisco Center Group)
My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel
92-321-2418349

8

`
Verification:

How to Set User Authentication in Switch:

MY_CISCO_CENTER #config terminal
MY_CISCO_CENTER (config)#line console 0
MY_CISCO_CENTER (config-line)# login
MY_CISCO_CENTER (config-line)#exit
MY_CISCO_CENTER (config)#username MCC password cisco123
MY_CISCO_CENTER (config)#exit
MY_CISCO_CENTER #exit
Verify the Authentication

From the Desk of Engr. Ahmed Saeed
Join Us on Facebook (My Cisco Center Group)
My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel
92-321-2418349

9

`

Configuring Telnet and SSH on Cisco Routers
OBJECTIVE:

Configuring the Cisco Router/Switch for remote access.
TOPOLOGY

How to Set Telnet password:

MY_CISCO_CENTER(config)#line vty 0 15
MY_CISCO_CENTER (config-line)#password cisco
MY_CISCO_CENTER (config-line)#login
MY_CISCO_CENTER (config-line)#exit
How to Enable The Device to Establish Telnet/SSH Session:

MY_CISCO_CENTER (config)#interface vlan 1
MY_CISCO_CENTER (config-if)#ip address 192.168.1.1 255.255.255.0
MY_CISCO_CENTER (config-if)#no shutdown

NOTE:

 Telnet is not recommended to access a device remotely, but you can use in a LAB
environment.
 For telnet, you must set the privileged password on router/switch. If not set, you will
not be able to access the device.

To access a Device using Telnet, from command prompt type:

C:\>telnet 192.168.1.1
Configuring SSH

MY_CISCO_CENTER (config)#username ahmed password cisco123
MY_CISCO_CENTER (config)#ip domain-name MY-CISCO-CENTER
MY_CISCO_CENTER (config)#crypto key generate rsa

From the Desk of Engr. Ahmed Saeed
Join Us on Facebook (My Cisco Center Group)
My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel
92-321-2418349

10

net Choose the size of the key modulus in the range of 360 to 2048 for your General Purpose Keys. Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349 11 .` The name for the keys will be: MY-CISCO-CENTER. How many bits in the modulus [512]: 512 % Generating 512 bit RSA keys … [OK] MY_CISCO_CENTER (config)#line vty 0 15 MY_CISCO_CENTER (config-line)#login local MY_CISCO_CENTER (config-line)#transport input ssh For SSH you need utilities like Secure CRT or putty to remotely access the device. From the Desk of Engr. Choosing a key modulus greater than 512 may take a few minutes.

while router restarts press the Ctrl+Break or Ctrl+C key to enter into ROM Monitor Mode. From the Desk of Engr.` Cisco Routers Password Recovery OBJECTIVE: To recover the console and enable password for Routers/Switches. restart the router. Configuration on Router MCC-R1>enable MCC-R1#config t MCC-R1 (config)#line console 0 MCC-R1 (config-line)Password cisco MCC-R1 (config-line)#Login MCCR1 (config-line)#Exit MCC-R1#copy running-config startup-config <To save the configurations) After these configurations. Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349 12 .

it will ignore the startup configurations in NVRAM. enter new configured password. to access the router. Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349 13 . Router#copy startup-config running-config Router(config)#enable password cisco Router(config)#config-register 0x2102 Router#copy running-config startup-config Restart the router. Now you can configure the following commands. for setting a new password. From the Desk of Engr.` In ROM Monitor Mode: Rommon 1 > confreg 0x2142 Rommon 2 > reset Once the Router/Switch is restarted.

Fa0/6. Fa0/22. Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349 14 .` Implementing Virtual Local Area Networks (VLANs) OBJECTIVE: To configure VLANs and Verify the configurations. Fa0/2.-------------------------------. Fa0/10. Fa0/18. Fa0/11. Fa0/3.------------------------------1 default active Fa0/1.--------. Fa0/24 Gig0/1. Fa0/19. Fa0/4 Fa0/5. Fa0/12 Fa0/13. TOPOLOGY Step: 1 to Create VLANs MY_CISCO_CENTER#config terminal MY_CISCO_CENTER (config)#vlan 10 MY_CISCO_CENTER (config-vlan)#name HR MY_CISCO_CENTER (config-vlan)#exit MY_CISCO_CENTER (config)#vlan 20 MY_CISCO_CENTER (config-vlan)#name IT MY_CISCO_CENTER (config-vlan)#exit Verify VLANs MY_CISCO_CENTER #show vlan brief VLAN Name Status Ports ---. Fa0/20 Fa0/21. Fa0/14. Fa0/8 Fa0/9. Fa0/15. Fa0/16 Fa0/17. Fa0/23. Gig0/2 10 HR active 20 IT active From the Desk of Engr. Fa0/7.

Fa0/23. Fa0/12 Fa0/13.` Step 2: Port Membership MY_CISCO_CENTER (config)#interface fa0/2 MY_CISCO_CENTER (config-if)#switchport mode access MY_CISCO_CENTER (config-if)#switchport access vlan 10 MY_CISCO_CENTER (config-if)#exit MY_CISCO_CENTER (config)#interface fa0/3 MY_CISCO_CENTER (config-if)#switchport mode access MY_CISCO_CENTER (config-if)#switchport access vlan 20 Switch# show vlan brief VLAN Name Status Ports ---. you need to configure Trunk Port between Switches. Fa0/24 Gig0/1. Fa0/10.-------------------------------. Gig0/2 Fa0/2 Fa0/3 NOTE: This is a Local VLAN. Fa0/7. Fa0/22.------------------------------- 10 20 HR IT active active 1 default active Fa0/1. Fa0/5. Fa0/19. Fa0/20 Fa0/21. Fa0/18. Fa0/8 Fa0/9.--------. . A trunk port carries traffic for multiple VLANs. Same configuration on both switches. Fa0/11. for End to End VLANs. Fa0/15. Fa0/14. Fa0/6. Fa0/16 Fa0/17.

Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349 15 .Trunk Port Configuration: Interface fa<port number> switchport mode trunk From the Desk of Engr.

Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349 16 .` Implementing VLAN Trunking Protocol Version 2 (VTP) OBJECTIVE: Configuring and verifying VTP Version 2 on Cisco Switches Configuring MCC-Switch-1: Switch(config)#hostname MCC-Switch-1 MCC-Switch-1(config)#exit MCC-Switch-1#show vtp status From the Desk of Engr.

` MCC-Switch-1#configure terminal MCC-Switch-1(config)#vtp domain MCC.COM Changing VTP domain name from NULL to MCC.COM MCC-Switch-1(config)#vlan 10 MCC-Switch-1(config-vlan)#name MCC-HR MCC-Switch-1(config-vlan)#exit MCC-Switch-1(config)#vtp password mcc123 MCC-Switch-1(config)#exit MCC-Switch-1#show vtp status Note:   VTP Password and domain name should be same on all Cisco switches  If you want to set revision number to zero set VTP mode to transparent  Best practice is to set VTP mode transparent then connect a new switch to your network. From the Desk of Engr. Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349 17 .

Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349 18 .` Implementing Port Based Security on Switches OBJECTIVE: Configure port security and verify the configurations. TOPOLOGY Switch Configurations MY_CISCO_CENTER(config)#interface range fa0/1-2 MY_CISCO_CENTER(config-if)#switchport mode access MY_CISCO_CENTER(config-if)#switchport port-security MY_CISCO_CENTER(config-if)#switchport port-security mac-address sticky MY_CISCO_CENTER(config-if)#switchport port-security maximum 1 MY_CISCO_CENTER(config-if)#switchport port-security violation shutdown MY_CISCO_CENTER(config-if)#exit NOTE: You can also use manual MAC address entry instead of sticky option. From the Desk of Engr.

` Verify Port-Security MAC Address: MY_CISCO_CENTER#show port-security Secure Port MaxSecureAddr CurrentAddr SecurityViolation Security Action (Count) (Count) (Count) --------------------------------------------------------------------------------------------------------------Fa0/1 1 1 0 Shutdown Fa0/2 1 1 0 Shutdown --------------------------------------------------------------------------------------------------------------- Verify Port-Security Interface FastEnthernet Fa0/1: MY_CISCO_CENTER #show port-security interface f0/1 Port Security: Port Status: Violation Mode: Aging Time: Aging Type: Secure Static Address Aging: Maximum MAC Addresses: Total MAC Addresses: Configured MAC Addresses: Sticky MAC Addresses: Last Source Address:Vlan : Security Violation Count: Enabled Secure-up Shutdown 0 mins Absolute Disabled 1 1 0 1 0010. restrict or shutdown From the Desk of Engr. Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349  19 . Violation modes can be set to protect.    Manual MAC  address can be entered in port-security instead on using sticky command.9B5E:1 0   Max Addresses value depends upon the model of the device.1110.

From the Desk of Engr. Verify when violation is occurred: MCC-SW1#show port-security Secure Port Ma SecureAddr CurrentAddr SecurityViolation Security Action (Count) (Count) (Count) -------------------------------------------------------------------------------------------------------------Fa0/1 1 1 1 Shutdown Fa0/2 1 1 1 Shutdown -------------------------------------------------------------------------------------------------------------- NOTE: When a port is shutdown. otherwise port will remain in error disabled mode. Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349 20 . then again no shut. you need to manually shutdown the port.` What happens if violation occurred? When a new PC is attached to the port on which port-security is enabled then Switch will take an action which is set in the violation mode.

1d) STP and (802.0C55. Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349 21 .4360 This bridge is the root Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Bridge ID Priority 32769 (priority 32768 sys-id-ext 1) Address 0090.1w) RSTP OBJECTIVE: To implement STP.` Implementing IEEE (802.4360 From the Desk of Engr. TOPOLOGY Verify Root Bridge on MCC-SW1: MCC-SW1#show spanning-tree VLAN0001 Spanning tree enabled protocol ieee Root ID Priority 32769 Address 0090. RSTP and manually make a bridge as root bridge.0C55.

and all switch ports are members of VLAN 1.  Default Priority is 32768.0C55.   While Bridge ID.0C55.  so the priority becomes 32768+Ext.--.1 P2p Desg FWD Fa0/2 Desg FWD 19 128. is Local Switch information. with default priority. Enabling RSTP: MCC-SW1(config)#spanning-tree mode rapid-pvst MCC1#show spanning-tree VLAN0001 Spanning tree enabled protocol rstp Root ID Priority 32769 Address 0090. having Lowest MAC address.------------------------------------------------------Fa0/1 19 128. Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349 22 .` Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Aging Time 20 Interface Role Sts Cost Prio.4360 Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Aging Time 20 From the Desk of Engr. VLAN ID which in this case is 1 (32768+1=32769).   As this bridge is the root bridge.2 P2p     In the output shown above.-------.--------.Nbr Type ------------.4360 This bridge is the root Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Bridge ID Priority 32769 (priority 32768 sys-id-ext 1) Address 0090. Run the same command on other switches and verify the Root Bridge.---. the parameters defined in Root ID corresponds to the Root Bridge information.

-------. Lowest Bridge/Switch ID.2127.Nbr Type ---------------. and Bridge ID is the combination or Bridge Priority and MAC address.--------------------------------------------------------------Fa0/1 Desg FWD 19 128.-------.--------.---. and you cannot change the MAC address.--------.2 P2p From the Desk of Engr.2 P2p Desg FWD Configuring MCC2 as the Root Bridge for VLAN 1:    As you know.--.15AC Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Aging Time 20 Interface Role Sts Cost Prio.` Interface Role Sts Cost Prio.15AC This bridge is the root Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Bridge ID Priority 4096 (priority 4096 sys-id-ext 1) Address 0090.Nbr Type ---------------.1 P2p Fa0/2 19 128. In order to manually make a switch as Root Bridge  we can only change its Priority. MCC2(config)#spanning-tree vlan 1 priority 4096 Verify MCC-SW2 as Root Bridge for VLAN 1: MCC-SW2#show spanning-tree VLAN0001 Spanning tree enabled protocol rstp Root ID Priority 4097 Address 0090. Priority of a Switch is changed in increments of 4096.2127.---. By default Bridge Priority is same.1 P2p Fa0/3 Desg FWD 19 128.--------------------------------------------------------------Fa0/2 Desg FWD 19 128.--. Switch will become  the Root Bridge. Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349 23 .

Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349 24 . connect a PC to the switch and the port will be up within 5 seconds.` Enabling Port fast feature on all switches: CONCEPT: By enabling portfast feature on all the switches. But the problem arises when a Switch is plug in. it can create switching loops. It will cause to take less time to change the state to up on all non-trucking ports. The solution to this problem is BPDU Guard. no switching loops will be created on Access Ports. switches will disable the STP process on all non-trunk ports. to a STP disabled port. To verify this feature. which will not listen Bridge Protocol Data Units (exchange of parameters between switches). MCC-SW1(config)#spanning-tree portfast default MCC-SW1(config)# spanning-tree bpduguard enable From the Desk of Engr.

Channel and verify the configurations TOPOLOGY Configuring MCC-SW1: MCC-SW1(config)#interface range fa0/1 .2 MCC-SW2 (config-if-range)#channel-protocol pagp MCC-SW2 (config-if-range)#channel group 1 mode desirable MCC-SW2 (config-if-range)#exit MCC-SW2 (config)#interface port-channel 1 MCC-SW2 (config-if)#switchport mode trunk From the Desk of Engr.2 MCC-SW1 (config-if-range)#channel-protocol pagp MCC-SW1 (config-if-range)#channel group 1 mode desirable MCC-SW1 (config-if-range)#exit MCC-SW1 (config)#interface port-channel 1 MCC-SW1 (config-if)#switchport mode trunk Configuring MCC-SW2: MCC-SW2(config)#interface range fa0/1 .` Implementing Link Aggregation (Ether-Channel) OBJECTIVE: To implement Layer 2 Ether. Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349 25 .

default port Number of channel-groups in use: 1 Number of aggregators: 1 Group Port-channel Protocol Ports -------------------------------------------------------------------------------------------------1 Po1(SU) PAgP From the Desk of Engr.Hot-standby (LACP only) R .Layer2 U .failed to allocate aggregator u .` Verify Etherchannel: MCC-SW1#show etherchannel summary Flags: D .in port-channel I .in use f . Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349 Fa0/1(P) Fa0/2(P) 26 .waiting to be aggregated d .suspended H .Layer3 S .unsuitable for bundling w .down P .stand-alone s .

` Implementing Inter-Vlan Routing using Router on a Stick OBJECTIVE: To configure and verify Inter-Vlan routing. using router on stick TOPOLOGY VLANs Creation: MCC1(config)#vlan 10 MCC1(config-vlan)#name HR MCC1(config-vlan)#exit MCC1(config)#vlan 20 MCC1(config-vlan)#name IT MCC1(config-vlan)#exit Port Assignment: MCC1(config)#interface fa0/1 MCC1(config-if)#switchport mode access MCC1(config-if)#switchport access vlan 10 MCC1(config-if)#exit MCC1(config)#interface fa0/2 MCC1(config-if)#switchport mode access MCC1(config-if)#switchport access vlan 20 MCC1(config-if)#exit From the Desk of Engr. Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349 27 .

0 MCC-R1(config-subif)#exit Creating sub-interface for VLAN 20 on router: MCC-R1(config)#interface gigabitEthernet 0/0.0.20 MCC-R1(config-subif)#encapsulation dot1Q 20 MCC-R1(config-subif)#ip address 11.0.0.0.10 MCC-R1(config-subif)#encapsulation dot1Q 10 MCC-R1(config-subif)#ip address 10.0.0 MCC-R1(config-subif)#exit PC0 Configurations From the Desk of Engr.0.` Trunk Port For Router On a Stick (The port connecting the Router) MCC1(config)#interface gigabitEthernet 0/1 MCC1(config-if)#switchport mode trunk Router Configurations: MCC-R1(config)#interface fa0/0 MCC-R1(config)#interface gigabitEthernet 0/0 MCC-R1(config-if)#no shutdown Creating sub-interface for VLAN 10 on router: MCC-R1(config)#interface gigabitEthernet 0/0.1 255.1 255.0. Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349 28 .0.

Ping PC1 from PC0 From the Desk of Engr. Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349 29 .` PC1 Configurations: Verify Inter-VLAN routing.

0. TOPOLOGY MCC-R2 Configurations: MCC-R2 (config)#interface serial 0/0 MCC-R2 (config-if)#ip address 200.2 255.255.255.252 MCC-R2 (config-if)#clock rate 64000 MCC-R2 (config-if)#no shutdown MCC-R2 (config)#interface fa2/0 MCC-R2 (config-if)#ip address 10.160.0. Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349 30 .0.1 255.0 MCC-R3 (config-if)#no shutdown From the Desk of Engr.100.1 255.0 MCC-R2 (config-if)#no shutdown MCC3 Configurations: MCC-R3 (config)#interface serial 2/0 MCC-R3 (config-if)#ip address 200.0.252 MCC-R3 (config-if)#no shutdown MCC-R3 (config)#interface fa0/0 MCC-R3 (config-if)#ip address 172.` Configuring Static Route on Cisco Routers OBJECTIVE: To configure and verify static routing.0.16.150.255.150.255.255.1 255.160.

160.IS-IS inter area * .RIP. FastEthernet2/0 S 172.0.OSPF external type 2. B .0 200.0.0 MCC-R2(config)#ip route 172.0/8 is directly connected.160.BGP D .periodic downloaded static route Gateway of last resort is not set C 10.0/30 is subnetted.e.OSPF inter area N1 .OSPF external type 1. Serial0/0 From the Desk of Engr. IA .0.0 255.0 255.150.OSPF NSSA external type 1.0. U . E .0.100.16. E2 . I .2 200. 1 subnets C 200.1 NOTE: When configuring the static route on router R1 we used the local interface of the router R1 i. R . O .EIGRP.candidate default.150.IS-IS level-2.16.16.150.per-user static route.EIGRP external. Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349 31 .0. EX .IGRP.0/16 [1/0] via 200. o . when configuring router R2 we use the next hop address as Forwarding router's address.0.0 200.IS-IS.` Static Routing: Adding static route on MCC-R2 for network 172. s0/1/0. N2 .255.160. S .2 Adding static route on MCC-R3 for network 10. Verify Routing MCC-R2#show ip route Codes: C . L2 .0 is directly connected.0. whereas.160.0.OSPF.150. L1 . ia .EGP i .0.connected.0.IS-IS level-1.mobile.0 MCC-R3(config)#ip route 10.static.160.ODR P .OSPF NSSA external type 2 E1 .150. M .

0.150.0/30 is subnetted. L2 . o .static. U .BGP D .160.IS-IS level-2.per-user static route.0.RIP.IS-IS inter area * .0.150.150.OSPF external type 1.ODR P . 1 subnets C 200.connected. E .IGRP.` Similarly on MCC-R3 MCC-R3#show ip route Codes: C .EIGRP. I . R .IS-IS level-1.160. M . IA . O . S .16.OSPF inter area N1 . N2 .OSPF external type 2. B . EX . FastEthernet0/0 200.mobile.EGP i .0 is directly connected. Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349 32 . Serial2/0 Verify the ping from PC0 to PC1 From the Desk of Engr.160.IS-IS. ia .periodic downloaded static route Gateway of last resort is not set S 10.0/16 is directly connected. L1 .1 C 172.EIGRP external.OSPF.candidate default.OSPF NSSA external type 2 E1 . E2 .0/8 [1/0] via 200.OSPF NSSA external type 1.

255.10.255.` Configuring Routing Information Protocol Version 2 OBJECTIVE: To configure and verify RIP V2 routing.0 MCC-R1(config-if)#no shutdown MCC-R1(config)#interface serial 3/0 MCC-R1(config-if)#ip address 200.160.150.150.1 255.2 255.255.0 MCC-R1(config-router)#network 10.160.252 MCC-R2(config-if)#no shutdown MCC-R2(config-if)#clock rate 64000 From the Desk of Engr.10.255.10.10.252 MCC-R1(config-if)#no shutdown MCC-R1(config)#router rip MCC-R1(config-router)#version 2 MCC-R1(config-router)#network 200.255.160.1 255.150. Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349 33 .0 Mcc-r2 configurations: MCC-R2(config)#interface serial 3/0 MCC-R2(config-if)#ip address 200. TOPOLOGY Mcc-r1 configurations: MCC-R1(config)#interface fa0/0 MCC-R1(config-if)#ip address 10.255.

255.252 MCC-R2(config-if)#no shutdown MCC-R2(config-if)#clock rate 64000 MCC-R2(config)#router rip MCC-R2(config-router)#version 2 MCC-R2(config-router)#network 200.150.16.16.2 255.255.160.160.39.0 MCC-R2(config-router)#network 150.100.39.39.0 MCC-R3(config-if)#no shutdown MCC-R3(config)#router rip MCC-R3(config-router)#version 2 MCC-R3(config-router)#network 172.160.160.1 255.255. Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349 34 .39.100.0 MCC-R2(config-router)#exit MCC-R2(config)#exit Mcc-r3 configurations: MCC-R3(config)#interface serial 2/0 MCC-R3(config-if)#ip address 150.0 MCC-R3(config-router)#network 150.0 MCC-R3(config-router)#exit MCC-R3(config)#exit Verify Routing Table on MCC-R1 From the Desk of Engr.160.1 255.255.255.252 MCC-R3(config-if)#no shutdown MCC-R3(config)#interface fa0/0 MCC-R3(config-if)#ip address 172.` MCC-R2(config-if)#exit MCC-R2(config)#interface serial 2/0 MCC-R2(config-if)#ip address 150.255.

` Verify end to end connectivity. ping MCC-PC2 from MCC-PC From the Desk of Engr. Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349 35 .

2 255.252 MCC-R2 (config-if)#clock rate 64000 MCC-R2 (config-if)#no shutdown MCC-R2 (config)#interface fa2/0 MCC-R2 (config-if)#ip address 10.0. Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349 36 .255.0 MCC-R2 (config-if)#no shutdown MCC3 Configurations: MCC-R3 (config)#interface serial 2/0 MCC-R3 (config-if)#ip address 200.0.255.255.1 255.252 From the Desk of Engr.160.0.150.0.150.160.1 255.` Implementing Enhanced Interior Gateway Routing Protocol (EIGRP) TOPOLOGY: MCC-R3 MCC-R2 MCC-R2 Configurations: MCC-R2 (config)#interface serial 0/0 MCC-R2 (config-if)#ip address 200.255.

150.160.16.0 MCC-R3 (config-router)#no auto-summary MCC-R3 (config-router)#exit Verify Routes on MCC-R2 MCC-R2#show ip route Gateway of last resort is not set C D C 10.160. 1 subnets 200.` MCC-R3 (config-if)#no shutdown MCC-R3 (config)#interface fa0/0 MCC-R3 (config-if)#ip address 172. 00:00:25.0 MCC-R3 (config-if)#no shutdown Adding networks for EIGRP on Router MCC-R2: MCC-R2(config)#router eigrp 10 MCC-R2 (config-router)#network 10.0/8 is directly connected.0. Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349 37 .16.0 MCC-R3 (config-router)#network 200.0.0.150. Serial0/0 200.150.0 is directly connected. FastEthernet2/0 172.255.0.160.0/16 [90/2172416] via 200.150.0 MCC-R2 (config-router)#network 200.0 MCC-R2 (config-router)#no auto-summary MCC-R2 (config-router)#exit Adding networks for EIGRP on Router MCC-R3: MCC-R3 (config)#router eigrp 10 MCC-R3 (config-router)#network 172.150.160.2.0/30 is subnetted.16.1 255.100.0.100.0.160. Serial0/0 From the Desk of Engr.

160.160.150.150.150. Serial2/0 To Verify Neighbor Relationship. use the following command : R1#show ip eigrp topology.0/30 is subnetted.0 is directly connected. Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349 38 .0.160.150.1 Se2/0 Hold Uptime SRTT RTO Q (sec) (ms) Cnt 13 00:09:27 40 1000 0 Seq Num 7 NOTE: To verify the currently enabled routing protocols. 1 subnets 200. by viewing Neighbor Table: Neighbor Table on MCC-R2 MCC-R2#show ip eigrp neighbors IP-EIGRP neighbors for process 10 H Address Interface 0 200.0/8 [90/20514560] via 200.160.0/16 is directly connected.150. From the Desk of Engr.2 Se0/0 Hold Uptime SRTT RTO (sec) (ms) Cnt 10 00:03:17 40 1000 Q 0 Seq Num 15 Neighbor Table on MCC-R3 IP-EIGRP neighbors for process 10 H Address Interface 0 200.0.0.160. Serial2/0 172.` Verify Routes on MCC-R3 MCC-R3#show ip route Gateway of last resort is not set D C C 10. 00:02:09.1. FastEthernet0/0 200. use the following command: R1#show ip protocols To view all the routes that has been calculated by EIGRP.16.

255.0.60.160.255.252 MCC-R0(config-if)#no shutdown MCC-R0(config-if)#clock rate 64000 Configuring Mcc-R1 MCC-R1(config)#interface serial 2/0 MCC-R1(config-if)#ip address 200.252 MCC-R1(config-if)#no shutdown MCC-R1(config-if)#clock rate 64000 From the Desk of Engr.0.255.1 255.0.2 255.255.1 255.150. Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349 39 .160.` Implementing Open Shortest Path First (OSPF) Version2 TOPOLOGY MCC-R1 MCC-R0 MCC-R2 Configuring MCC-R0 MCC-R0(config)#interface fa0/0 MCC-R0(config-if)#ip address 10.1 255.0 MCC-R0(config-if)#no shutdown MCC-R0(config)#interface serial 2/0 MCC-R0(config-if)#ip address 200.0.37.255.255.252 MCC-R1(config-if)#no shutdown MCC-R1(config)#interface serial 3/0 MCC-R1(config-if)#ip address 139.150.

`
Configuring MCC-R2

MCC-R2(config)#interface serial 2/0
MCC-R2(config-if)#ip address 139.60.37.2 255.255.255.252
MCC-R2(config-if)#no shutdown
MCC-R2(config)#interface fa0/0
MCC-R2(config-if)#ip address 172.16.0.1 255.255.0.0
MCC-R2(config-if)#no shutdown
Configuring MCC-R1
The Area Border Router

MCC-R1(config)#router ospf 10
MCC-R1(config-router)#network 200.150.160.0 0.0.0.3 area 0
MCC-R1(config-router)#network 139.60.37.0 0.0.0.3 area 1
Configuring MCC-R0
The BACKBONE Area Router

MCC-R0(config)#router ospf 100
MCC-R0(config-router)#network 10.0.0.0 0.255.255.255 area 0
MCC-R0(config-router)#network 200.150.160.0 0.0.0.3 area 0
Configuring MCC-R2
Regular Area Router, Internal Router

MCC-R2(config)#router ospf 50
MCC-R2(config-router)#network 139.60.37.0 0.0.0.3 area 1
MCC-R2(config-router)#network 172.16.0.0 0.0.255.255 area 1
Verify Routes on ABR:
MCC-R1#show ip route

Gateway of last resort is not set

O
C
O
C

10.0.0.0/8 [110/65] via 200.150.160.1, 00:12:21, Serial2/0
139.60.0.0/30 is subnetted, 1 subnets
139.60.37.0 is directly connected, Serial3/0
172.16.0.0/16 [110/65] via 139.60.37.2, 00:03:03, Serial3/0
200.150.160.0/30 is subnetted, 1 subnets
200.150.160.0 is directly connected, Serial2/0

From the Desk of Engr. Ahmed Saeed
Join Us on Facebook (My Cisco Center Group)
My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel
92-321-2418349

40

`
Verify Routes on MCC-R0 (Backbone Router)

MCC-R0#show ip route
Gateway of last resort is not set

C

10.0.0.0/8 is directly connected, FastEthernet0/0
139.60.0.0/30 is subnetted, 1 subnets
O 139.60.37.0 [110/128] via 200.150.160.2, 00:19:03, Serial2/0
0IA 172.16.0.0/16 [110/129] via 200.150.160.2, 00:09:42, Serial2/0
200.150.160.0/30 is subnetted, 1 subnets
C
200.150.160.0 is directly connected, Serial2/0
Verify Routes on MCC-R2 (Internal Router)

MCC-R2#show ip route
Gateway of last resort is not set
O 10.0.0.0/8 [110/129] via 139.60.37.1, 00:17:38, Serial2/0
139.60.0.0/30 is subnetted, 1 subnets
C
139.60.37.0 is directly connected, Serial2/0
C
172.16.0.0/16 is directly connected, FastEthernet0/0
200.150.160.0/30 is subnetted, 1 subnets
O IA 200.150.160.0 [110/128] via 139.60.37.1, 00:17:38, Serial2/0
Verify end to end connectivity

Ping from PC0 to PC1

Note: More commands to verify OSPF:
MCC-R1#show ip ospf neighbor
MCC-R1#show ip ospf database
MCC-R1#show ip protocols
MCC-R1#show ip ospf interface
From the Desk of Engr. Ahmed Saeed
Join Us on Facebook (My Cisco Center Group)
My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel
92-321-2418349

41

`

Implementing IPV6 on Cisco Routers
TOPOLOGY

MCC-R1 Configuration

MCC-R1(config)#ipv6 unicast-routing
MCC-R1(config)#interface serial 1/0
MCC-R1(config-if)#ipv6 address 2001:abad:beef:1::1/64
MCC-R1(config-if)#no shutdown
MCC-R2 Configuration

MCC-R2(config)#ipv6 unicast-routing
MCC-R2(config)#interface serial 1/0
MCC-R2(config-if)#ipv6 address 2001:abad:beef:1::2/64
MCC-R2(config-if)#no shutdown
Verify Configurations

MCC-R1# show ipv6 interface

From the Desk of Engr. Ahmed Saeed
Join Us on Facebook (My Cisco Center Group)
My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel
92-321-2418349

42

` MCC-R2# show ipv6 interface Verify IPv6 communication between R2 and R1 using ping: From the Desk of Engr. Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349 43 .

` Configuring IPV6 Stateless Auto Configuration OBJECTIVE: To configure State less auto IPv6 configurations on Cisco Routers TOPOLOGY Mcc-r1 configurations: MCC-R1(config)#ipv6 unicast-routing MCC-R1(config)#interface fa0/0 MCC-R1(config-if)#ipv6 address 2001:abad:5001:1::1/64 MCC-R1(config-if)#ipv6 address prefix 2001:abad:5001:1::/64 MCC-R1(config-if)#no shutdown Mcc-r2 configurations: MCC-R2(config)#ipv6 unicast-routing MCC-R2(config)#interface fa0/0 MCC-R2(config-if)#ipv6 address autoconfig MCC-R2(config-if)#no shutdown From the Desk of Engr. Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349 44 .

` Mcc-r3 configurations: MCC-R3(config)#ipv6 unicast-routing MCC-R3(config)#interface fa0/0 MCC-R3(config-if)#ipv6 address autoconfig MCC-R3(config-if)#no shutdown Verify configurations: From the Desk of Engr. Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349 45 .

All the interfaces are configured with the IPv6 addresses Mcc-r1 configurations: MCC-R1(config)#interface serial 1/0 MCC-R1(config-if)#ipv6 address 2001:abad:5001:1::1/64 MCC-R1(config-if)#ipv6 rip MY-CISCO-CENTER enable MCC-R1(config-if)#no shutdown MCC-R1(config-if)#exit MCC-R1(config)#interface loopback 10 MCC-R1(config-if)#ipv6 address 1:1:1:1::1/64 MCC-R1(config-if)#ipv6 rip MY-CISCO-CENTER enable MCC-R1(config-if)#no shutdown MCC-R1(config)#interface loopback 15 MCC-R1(config-if)#ipv6 address 1:1:1:2::1/64 MCC-R1(config-if)#ipv6 rip MY-CISCO-CENTER enable MCC-R1(config-if)#no shutdown Mcc-r2 configurations: MCC-R2(config)#IPV6 unicast-routing MCC-R2(config)#interface serial 1/0 MCC-R2(config-if)#ipv6 address 2001:abad:5001:1::2/64 MCC-R2(config-if)#ipv6 rip MY-CISCO-CENTER enable MCC-R2(config-if)#no shutdown MCC-R2(config)#interface loopback 0 MCC-R2(config-if)#ipv6 address 2:2:2:2::1/64 MCC-R2(config-if)#ipv6 rip MY-CISCO-CENTER enable MCC-R2(config-if)#no shutdown MCC-R2(config)#interface loopback 1 From the Desk of Engr. Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349 46 . routers R1 and R2 are connected via Serial interface and Loopback addresses are configured to generate networks.` Implementing Ripng on Cisco Routers OBJECTIVE: To configure and verify RIPng on Cisco Routers TOPOLOGY BACKGROUND: In this configuration example.

` MCC-R2(config-if)#ipv6 address 2:2:2:1::1/64 MCC-R2(config-if)#ipv6 rip MY-CISCO-CENTER enable MCC-R2(config-if)#no shutdown Verify Configurations And Connectivity To view the ipv6 routing Table Verify information about the current IPv6 RIP process From the Desk of Engr. Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349 47 .

Verify the reachability between the routers R1 and R2.` Verify the details of entries in current rip routing instance. Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349 48 . use the ping command From the Desk of Engr.

` Implementing Open Shortest Path First (OSPF) Version 3 OBJECTIVE: To configure and Verify OSPF Version 3 on Cisco Routers TOPOLOGY Configuration On Mcc-R1 MCC-R1 (config)#ipv6 unicast-routing MCC-R1 (config)#interface fastEthernet 0/0 MCC-R1 (config-if)#ipv6 address 2001:abad:5001:1::1/64 MCC-R1 (config-if)#no shutdown MCC-R1 (config-if)#ipv6 ospf 1 area 0 MCC-R1 (config-if)#exit MCC-R1 (config)#interface loopback 10 MCC-R1 (config-if)#ipv6 address 1:1:1:1::1/64 MCC-R1 (config-if)#ipv6 ospf 1 area 0 MCC-R1 (config-if)#no shutdown MCC-R1 (config-if)#exit MCC-R1 (config)#interface loopback 20 MCC-R1 (config-if)#ipv6 address 1:1:1:2::1/64 MCC-R1 (config-if)#ipv6 ospf 1 area 0 MCC-R1 (config-if)#no shutdown MCC-R1 (config-if)#e MCC-R1 (config-if)#exit MCC-R1 (config)#ipv6 router ospf 1 MCC-R1 (config-rtr)#router-id 1.1.1.1 From the Desk of Engr. Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349 49 .

To change OSPF to advertise the subnet assigned to the loopback interface you’ll need to change the network type to point-to-point as shown below MCC-R1 MCC-R1(config)#interface loopback 10 MCC-R1(config-if)#ipv6 ospf 1 area 0 MCC-R1(config-if)#ipv6 ospf network point-to-point From the Desk of Engr. NOTE: Loopback interfaces have their own OSPF network type in which case OSPF advertises a host route to the loopback interface and not the configure subnet mask.2. 20 and R2’s Loopback 0. 1 interface to participate in OSPF Area 0 and ensure that R1 & R2 advertises Lo0 as a /64 subnet and not a host route (/128).` Configurations On Mcc-R2 MCC-R2(config)#ipv6 unicast-routing MCC-R2(config)#interface fa0/0 MCC-R2(config-if)#ipv6 address 2001:abad:5001:1::2/64 MCC-R2(config-if)#no shutdown MCC-R2(config-if)#ipv6 ospf 1 area 0 MCC-R2(config-if)#exit MCC-R2(config)#interface loopback 0 MCC-R2(config-if)#ipv6 address 2:2:2:2::1/64 MCC-R2(config-if)#ipv6 ospf 1 area 0 MCC-R2(config-if)#no shutdown MCC-R2(config-if)#exit MCC-R2(config)#interface loopback 1 MCC-R2(config-if)#ipv6 address 2:2:2:1::1/64 MCC-R2(config-if)#ipv6 ospf 1 area 0 MCC-R2(config-if)#no shutdown MCC-R2(config-if)#exit MCC-R2(config)#ipv6 router ospf 1 MCC-R2(config-rtr)#router-id 2.2. Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349 50 .2 Configure R1′s Loopback 10.

` MCC-R1(config)#interface loopback 20 MCC-R1(config-if)#ipv6 ospf 1 area 0 MCC-R1(config-if)#ipv6 ospf network point-to-point MCC-R2 MCC-R2(config)#interface loopback 0 MCC-R2(config-if)#ipv6 ospf 1 area 0 MCC-R2(config-if)#ipv6 ospf network point-to-point MCC-R2(config-if)#exit MCC-R2(config)#interface loopback 1 MCC-R2(config-if)#ipv6 ospf 1 area 0 MCC-R2(config-if)#ipv6 ospf network point-to-point Verify R1′s Loopback0 network is in the IPv6 routing table of R2: MCC-R1#show ipv6 route ospf From the Desk of Engr. Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349 51 .

Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349 52 .` Verify R1′s Loopback10 network has IPv6 connectivity to R2′s Loopback0 network using PING: From the Desk of Engr.

1 MCC-R1(config-rtr)#exit MCC-R1(config)#interface loopback 10 MCC-R1(config-if)#ipv6 address 1:1:1:1::1/64 MCC-R1(config-if)#no shutdown MCC-R1(config-if)# ipv6 eigrp 100 MCC-R1(config-if)#exit MCC-R1(config)#interface loopback 20 MCC-R1(config-if)#ipv6 address 1:1:1:2::1/64 MCC-R1(config-if)#no shutdown MCC-R1(config-if)#ipv6 eigrp 100 MCC-R1(config-if)#exit From the Desk of Engr.1.1.` Implementing EIGRP for IPV6 Networks OBJECTIVE: To configure and verify EIGRP for IPV6 TOPOLOGY Configurations On Mcc-R1 MCC-R1(config)#ipv6 unicast-routing MCC-R1(config)#interface serial 1/0 MCC-R1(config-if)#ipv6 address 2001:abad:5001:1::1/64 MCC-R1(config-if)#no shutdown MCC-R1(config)#ipv6 router eigrp 100 MCC-R1(config-rtr)#eigrp router-id 1. Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349 53 .

2 MCC-R2(config-rtr)#exit MCC-R2(config)#interface loopback 0 MCC-R2(config-if)#ipv6 address 2:2:2:2::1/64 MCC-R2(config-if)#no shutdown MCC-R2(config-if)#ipv6 eigrp 100 MCC-R2(config-if)#exit MCC-R2(config)#int MCC-R2(config)#interface loopback 1 MCC-R2(config-if)#ipv6 address 2:2:2:1::1/64 MCC-R2(config-if)#no shutdown MCC-R2(config-if)#ipv6 eigrp 100 From the Desk of Engr. Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349 54 .2.2.` Configurations On Mcc-R2 MCC-R2(config)#ipv6 unicast-routing MCC-R2(config)#interface serial 1/0 MCC-R2(config-if)#ipv6 address 2001:abad:5001:1::2/64 MCC-R2(config-if)#no shutdown MCC-R2(config-if)#ipv6 eigrp 100 MCC-R2(config)#ipv6 router eigrp 100 MCC-R2(config-rtr)#eigrp router-id 2.

Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349 55 .` Verify R1′s Loopback0 network is in the IPv6 routing table of R2: R1#show ipv6 route eigrp Check connectivity From the Desk of Engr.

168.0 255.1.0 MCC-DHCP-SERVER(dhcp-config)#default-router 192.168. TOPOLOGY Configurations On Mcc-Dhcp-Server MCC-DHCP-SERVER(config)#ip dhcp pool MCC-DHCP-POOL1 MCC-DHCP-SERVER(dhcp-config)#network 192.1. Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349 56 .10 From the Desk of Engr.1 MCC-DHCP-SERVER(dhcp-config)#exit MCC-DHCP-SERVER(config)#ip dhcp excluded-address 192.1.168.` Configuring DHCP on Cisco Routers OBJECTIVE: To Configure Cisco Routers as a DHCP Server and Verify the services.255.255.

You can also configure Multiple DHCP pools for VLANs on a single DHCP Server. DNS Servers etc. Verify the DHCP Server Configurations: From the Desk of Engr. or reserved addresses for Web Servers.` NOTE: You can exclude the range of addresses which should not be assigned to host machines. Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349 57 .

Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349 58 .` Address Leases on DHCP Server: MCC-DHCP-SERVER # show ip dhcp binding From the Desk of Engr.

16.0 MCC-R1(config-if)#exit From the Desk of Engr.0 MCC-R1(config-if)#no shutdown MCC-R1(config)#interface fa1/0 MCC-R1(config-if)#ip address 172.100.1. Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349 59 .255.255.1 255. TOPOLOGY Mcc-r1 configurations: MCC-R1(config)#interface fa0/0 MCC-R1(config-if)#ip address 192.255.168.1 255.` Implementing Standard and Extended Access Control List (ACL) OBJECTIVE: To implement standard and extended access control lists to limit the access.255.

` Ping from MCC-PC1 to MCC-PC2 Now restrict the MCC-PC1 to communicate with MCC-PC using standard ACL.1. Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349 60 . MCC-R1(config)#access-list 50 deny host 192.2 MCC-R1(config)#interface fa0/0 MCC-R1(config-if)#ip access-group 50 in MCC-R1(config-if)#exit From the Desk of Engr.168.

` Now check the connectivity from MCC-PC1 to MCC-PC2 From the Desk of Engr. Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349 61 .

100.252 MCC-R1 (config-if)#no shutdown MCC-R1 (config)#router eigrp 10 MCC-R1 (config-router)#network 200.0.0.168.0 0.100.168.255.16.150.2 host 172.255.1 255.3 host 172.255 MCC-R1 (config-router)#no auto-summary MCC-R1 (config-router)#exit MCC-R1 (config)#access-list 100 permit tcp host 192.50 eq 80 MCC-R1 (config)#access-list 100 deny tcp host 192.16.150.0 0.` EXTENDED ACL TOPOLOGY  The task is to permit MCC-PC1 on LAN 1 only WEB access to MYCISCOCENTER Webserver.1.0.168.3 MCC-R1 (config-router)#network 192.1.1.255. Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349 62 .0.0 MCC-R1 (config-if)#no shutdown MCC-R1 (config)#interface fa1/0 MCC-R1 (config-if)#ip address 200.1.1 255. Configuration On Mcc-R1 MCC-R1(config)#interface fa0/0 MCC-R1 (config-if)#ip address 192.168.   Block MCC-PC1 from accessing the MYCISCOCENTER Webserver through WWW.160.160.50 eq 80 MCC-R1 (config)#access-list 100 permit ip any any From the Desk of Engr.255.

0.16.2 255.255 MCC-R2 (config-router)#no auto-summary MCC-R2 (config)#exit Verification: Accessing the Web Server from MCC-PC1 From the Desk of Engr.255.255.` MCC-R1 (config)#interface fa0/0 MCC-R1 (config-if)#ip access-group 100 in Mcc-r2 configurations: MCC-R2 (config)#interface fa0/0 MCC-R2 (config-if)#ip address 200.100.160.255.0 0.0.150.252 MCC-R2 (config-if)#no shutdown MCC-R2 (config)#interface fa1/0 MCC-R2 (config-if)#ip address 172.3 MCC-R2 (config-router)#network 172.150.0 MCC-R2 (config-if)#no shutdown MCC-R2 (config)#exit MCC-R2 (config)#router eigrp 10 MCC-R2 (config-router)#network 200. Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349 63 .160.16.0 0.255.1 255.0.0.100.

Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349 64 .` Accessing Web Server from MCC-PC2 From the Desk of Engr.

1.3 MCC-R1 (config-router)#network 192. Dynamic and PAT) OBJECTIVE: To configure and Verify Static.255.160.0. Dynamic and PAT. TOPOLOGY Mcc-r1 configurations: MCC-R1 (config)#interface fa0/0 MCC-R1 (config-if)#ip address 192.160.168.0 0.252 MCC-R1 (config-if)#no shutdown MCC-R1 (config)#router eigrp 10 MCC-R1 (config-router)#network 200.0 MCC-R1 (config-if)#no shutdown MCC-R1 (config)#interface fa1/0 MCC-R1 (config-if)#ip address 200.150.255.` Implementing Network Address Translation (Static.255.0.1 255.0 0. Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349 65 .168.255 MCC-R1 (config-router)#no auto-summary MCC-R1 (config-router)#exit From the Desk of Engr.0.1.0.1 255.150.255.

3 MCC-R2 (config-router)#network 172.252 MCC-R2 (config-if)#no shutdown MCC-R2 (config)#interface fa1/0 MCC-R2 (config-if)#ip address 172.16. By Using Command MCC-R1#show ip nat translation From the Desk of Engr.160.0.160.1.255.150.150.255 MCC-R2 (config-router)#no auto-summary MCC-R2 (config)#exit CONFIGURING STATIC NAT FOR MCC-PC1 WITH PUBLIC IP 200.255.0 MCC-R2 (config-if)#no shutdown MCC-R2 (config)#exit MCC-R2 (config)#router eigrp 10 MCC-R2 (config-router)#network 200.160.0.255.168.100.0 0.255.2 200.150.0.0 0.1 MCC-R1(config)#interface fa0/0 MCC-R1(config-if)#ip nat inside MCC-R1(config-if)#exit MCC-R1(config)#interface fa1/0 MCC-R1(config-if)#ip nat outside Verify.100. Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349 66 .2 255.` Mcc-r2 configurations: MCC-R2 (config)#interface fa0/0 MCC-R2 (config-if)#ip address 200.160.1 255.150.16.0.1 MCC-R1(config)#ip nat inside source static 192.

255.0.252 MCC-R1 (config-if)#no shutdown MCC-R1 (config)#router eigrp 10 MCC-R1 (config-router)#network 200.255.0.160.1.0.3 MCC-R1 (config-router)#network 192.160. Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349 67 .0 MCC-R1 (config-if)#no shutdown MCC-R1 (config)#interface fa1/0 MCC-R1 (config-if)#ip address 200.168.168.150.255 MCC-R1 (config-router)#no auto-summary MCC-R1 (config-router)#exit Mcc-r2 configurations: From the Desk of Engr.1 255.1.` DYNAMIC NAT TOPOLOGY Mcc-r1 configurations: MCC-R1 (config)#interface fa0/0 MCC-R1 (config-if)#ip address 192.0 0.1 255.150.0.0 0.255.255.

0 MCC-R1(config)#access-list 10 permit any MCC-R1(config)#ip nat inside source list 10 pool DYNAMIC-NAT MCC-R1(config)#interface fa0/0 MCC-R1(config-if)#ip nat inside MCC-R1(config)#interface fa1/0 MCC-R1(config-if)#ip nat outside VERIFY: From the Desk of Engr.3.100.60.255.255.139.255.2 180.60.252 MCC-R2 (config-if)#no shutdown MCC-R2 (config)#interface fa1/0 MCC-R2 (config-if)#ip address 172. MCC-R1(config)#ip nat pool DYNAMIC-NAT 180.255.139.255.1 255.139.2 255.3 netmask 255.60.0 MCC-R2 (config-if)#no shutdown MCC-R2 (config)#exit Configuring Dynamic NAT for MCC-PC1 and MCC-PC2 with IP addresses 180.16.255.60.139. Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349 68 .` MCC-R2 (config)#interface fa0/0 MCC-R2 (config-if)#ip address 200.160.2 180.150.

160.0 MCC-R1 (config-if)#no shutdown MCC-R1 (config)#interface fa1/0 MCC-R1 (config-if)#ip address 200.1 255. Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349 69 .16.255.1.` PAT TOPOLOGY Mcc-r1 configurations: MCC-R1 (config)#interface fa0/0 MCC-R1 (config-if)#ip address 192.0.255.1 255.1 255.252 MCC-R1 (config-if)#no shutdown MCC-R1 (config)#router eigrp 10 MCC-R1 (config-router)#network 200.150.168.255.252 MCC-R2 (config-if)#no shutdown MCC-R2 (config)#interface fa1/0 MCC-R2 (config-if)#ip address 172.255.0 0.0.150.2 255.255.0 From the Desk of Engr.0.150.255 MCC-R1 (config-router)#no auto-summary MCC-R1 (config-router)#exit Mcc-r2 configurations: MCC-R2 (config)#interface fa0/0 MCC-R2 (config-if)#ip address 200.0.255.3 MCC-R1 (config-router)#network 192.255.160.160.100.168.255.1.0 0.

1.160. Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349 70 .160.` MCC-R2 (config-if)#no shutdown MCC-R2 (config)#exit Configuring Port Address Translation with public IP addresses 200.255.150. MCC-R1(config)#ip nat pool PAT 200.160.252 MCC-R1(config)#access-list 10 permit any MCC-R1(config)#ip nat inside source list 10 pool PAT overload MCC-R1(config)#interface fa0/0 MCC-R1(config-if)#ip nat inside MCC-R1(config)#interface fa1/0 MCC-R1(config-if)#ip nat outside VERIFICATION: From the Desk of Engr.150.150.1 200.255.1 netmask 255.

` Implementing Hot Standby Routing Protocol(HSRP) TOPOLOGY From the Desk of Engr. Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349 71 .

168.0.255. Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349 72 .0 0.1.16.0.0.0 MCC-R1(config)#router eigrp 10 MCC-R1(config-router)#network 200.0.3 MCC-R1(config-router)#network 172.168.0.10.168.1 255.0 MCC-R2(config-if)#no shutdown MCC-R2(config)#router eigrp 10 MCC-R2(config-router)#network 172.252 MCC-R1(config-if)#no shutdown MCC-R1(config-if)#clock rate 64000 MCC-R1(config)#interface serial 3/0 MCC-R1(config-if)#ip address 172.16.100.0 0.10.255.0.160.255.2 MCC-R3(config-if)#no shutdown MCC-R3(config)#router eigrp 10 MCC-R3(config-router)#network 10.255.16.150.0.0 0.` Configuring MCC-R1 (WAN Router) MCC-R1(config)#interface serial 2/0 MCC-R1(config-if)#ip address 10.255.100.16.168.100.10.2 255.3 MCC-R3(config-router)#network 192.10.2 255.255.252 MCC-R1(config-if)#clock rate 64000 MCC-R1(config)#interface loopback 0 MCC-R1(config-if)#ip address 200.1 255.1.100.3 MCC-R1(config-router)#no auto-summary MCC-R1(config-router)#exit Configuring MCC-R2 (HSRP Group 1 Router) MCC-R2(config)#interface serial 2/0 MCC-R2(config-if)#ip address 172.255.0 0.150.255.0.1 255.10.255.0.255.1.0.0.1 255.160.255 MCC-R2(config-router)#no auto-summary Configuring MCC-R3 (HSRP Group 1 Router) MCC-R3(config)#interface serial 2/0 MCC-R3(config-if)#ip address 10.3 MCC-R2(config-router)#network 192.0.255.252 MCC-R2(config-if)#no shutdown MCC-R2(config)#interface gigabitEthernet 6/0 MCC-R2(config-if)#ip address 192.252 MCC-R3(config-if)#no shutdown MCC-R3(config)#interface gigabitEthernet 6/0 MCC-R3(config-if)#ip address 192.10.255 MCC-R3(config-router)#no auto-summary CONFIGURING HSRP ON MCC-R2 From the Desk of Engr.0 0.1.0 0.255.

100 MCC-R2(config-if)#standby 1 priority 110 MCC-R2(config-if)#standby 1 preempt MCC-R2(config-if)#standby 1 track serial 2/0 CONFIGURING HSRP ON MCC-R3 MCC-R3(config)#interface GigabitEthernet 6/0 MCC-R3(config-if)#standby 1 ip 192. Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349 73 .168.100 MCC-R3(config-if)#standby 1 priority 95 MCC-R2(config-if)#standby 1 preempt Verify the configurations: MCC-R2#show standby From the Desk of Engr.1.` MCC-R2(config)#interface GigabitEthernet 6/0 MCC-R2(config-if)#standby 1 ip 192.168.1.

Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349 74 .` Similarly on MCC-R3 MCC-R3#show standby From the Desk of Engr.

Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349 75 .255.255.255.160.` Implementing Wan Encapsulation OBJECTIVE: To configure PPP WAN Encapsulation.252 MCC-R1(config-if)#no shutdown MCC-R1(config-if)#clock rate 64000 MCC-R1(config-if)#encapsulation ppp MCC-R1(config-if)#ppp authentication chap pap MCC-R1(config)#username MCC-R2 password cisco (Other side Router parameters) MCC-R1(config)#exit Configurations On Mcc-R2 MCC-R2(config)#username MCC-R2 password cisco MCC-R2(config)#interface serial 1/0 MCC-R2(config-if)#ip address 200. TOPOLOGY Configurations On Mcc-R1 MCC-R1(config)#username MCC-R1 password cisco MCC-R1(config)#interface serial 1/0 MCC-R1(config-if)#ip address 200.150.255.2 255.150.160.252 MCC-R2(config-if)#no shutdown MCC-R2(config-if)#encapsulation ppp MCC-R2(config-if)#ppp authentication chap pap MCC-R2(config)#username MCC-R1 password cisco(Other side Router parameters) MCC-R2(config)#exit From the Desk of Engr.1 255.

` Verify point-to-point connectivity: R1#ping 192.168. Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349 76 .2 From the Desk of Engr.1.

10.255.` TFTP SERVER OBJECTIVE: System IOS and Running-Configuration to a remote TFTP server.0 MCC-R1(config-if)#no shutdown MCC-R1(config)#interface serial 3/0 MCC-R1(config-if)#ip address 200. MCC-TFTP-SERVER (BEFORE COPYING FILES) From the Desk of Engr.255.10.252 MCC-R1(config-if)#no shutdown MCC-R1(config)#router rip MCC-R1(config-router)#version 2 MCC-R1(config-router)#network 200.160.1 255.10.0 MCC-R1(config-router)#network 10.160.255.1 255.150.255.150.10. Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349 77 . TOPOLOGY Configuring the Router in order to save these configurations and then copy to TFTP Server MCC-R1(config)#interface fa0/0 MCC-R1(config-if)#ip address 10.

122-28.122-28.5571584 bytes] 5571584 bytes copied in 3.10. Which files you want to copy to TFTP server. I will copy this IOS to TFTP Server.bin is present.12228.` You can see..bin. As you can see the IOS image with extension of .162 secs (403737 bytes/sec) From the Desk of Engr. then starup-config. Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349 78 . To copy files to TFTP Server MCC-R1#copy flash: tftp: Source filename []? pt1000-i-mz.bin]? <if you want to save this file with different name specify here. currently there are no files present on TFTP server. otherwise press enter to save with default name> Writing pt1000-i-mz..10.bin Address or name of remote host []? 10.10 Destination filename [pt1000-i-mz.!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! ! [OK . first you should know their names..

001 secs (778000 bytes/sec) From the Desk of Engr.!! [OK . COPYING STARTUP-CONFIG MCC-R1#copy startup-config tftp: Address or name of remote host []? 10. Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349 79 .10..778 bytes] 778 bytes copied in 0..10.` Now verify the IOS on TFTP Server.10 Destination filename [MCC-R1-confg]? MCC-R1_startup-config Writing startup-config.

TFTP Server. Router IOS and Starup-config has been copied to secure location. NOTE: By following the same procedure.` MCC-R1# VERIFICATION: You can see both. you can copy files from TFTP Server to the device. Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349 80 . From the Desk of Engr.

` FTP SERVER OBJECTIVE: System IOS and Running-Configuration to a remote FTP server. These credentials will be used to copy to files to FTP Server.1 255.255.252 MCC-R1(config-if)#no shutdown MCC-R1(config)#router rip MCC-R1(config-router)#version 2 MCC-R1(config-router)#network 200.10.10.1 255.160.10. this username and password is also configured on Router as it is. TOPOLOGY MCC-R1(config)#interface fa0/0 MCC-R1(config-if)#ip address 10. Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349 81 .255.160.10.0 MCC-R1(config-router)#network 10.255.255.150. For FTP you need to create a user on FTP server. MCC-R1(config)#ip ftp username MCCFTP MCC-R1(config)#ip ftp password cisco123 From the Desk of Engr.0 MCC-R1(config-if)#no shutdown MCC-R1(config)#interface serial 3/0 MCC-R1(config-if)#ip address 200.150.

5571584 bytes] 5571584 bytes copied in 10.754 secs (518000 bytes/sec) Copy startup-config MCC-R1#copy startup-config ftp: Address or name of remote host []? 10.10 Destination filename [pt1000-i-mz.10.. [OK .039 secs (21000 bytes/sec) From the Desk of Engr.10.10..122-28.. Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349 82 .846 bytes] 846 bytes copied in 0.` Copy IOS: MCC-R1#copy flash: ftp: Source filename []? pt1000-i-mz.bin.bin]? Writing pt1000-i-mz.10 Destination filename [MCC-R1-confg]? MCC-R1-Configurations Writing startup-config.122-28. [OK .122-28.bin Address or name of remote host []? 10..10.

Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349 83 . you can copy files from TFTP Server to the device. From the Desk of Engr.` Verify on FTP Server: NOTE: By following the same procedure.

they will be reported to syslog server. From the Desk of Engr.1 255.255.16.255.0 MCC-R1(config-if)#no shutdown MCC-R1(config)#logging on MCC-R1(config)#service timestamps debug datetime msec MCC-R1(config)#logging host 172.0 MCC-R1(config-if)#no shutdown MCC-R1(config)#interface fa1/0 MCC-R1(config-if)#ip address 172.16.100.` Configuring SYSLOG Server OBJECTIVE: To Implement Syslog Server TOPOLOGY : MCC-R1(config)#INterface fa0/0 MCC-R1(config-if)#ip address 192.1 255.100.1.255.100 MCC-R1(config)#logging trap debugging Now perform some tasks on router.168. Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349 84 .255.

` Verification: From the Desk of Engr. Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349 85 .

Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349 86 .` PPP MULTILINK LAB CONFIGURATION ON R4: From the Desk of Engr.

CONFIGURATION ON R5: From the Desk of Engr. Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349 87 .

Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349 88 .Verification of PPP Multilink on R4 & R5 : From the Desk of Engr.

Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349 89 .From the Desk of Engr.

GRE TUNNEL CONFIGURATION OF GRE ON R1 & R2 From the Desk of Engr. Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349 90 .

Ahmed Saeed Join Us on Facebook (My Cisco Center Group) My Cisco Center (MCC) Block 6 PECHS Near Farhan Hotel 92-321-2418349 .From the Desk of Engr.

Master your semester with Scribd & The New York Times

Special offer for students: Only $4.99/month.

Master your semester with Scribd & The New York Times

Cancel anytime.
ciscoexam-online-sale-200-125-exam    | udemy-newccnax-sale-200-125-exam    | whats-new-with-ccna-sale-200-125-exam    | ccna-practice-quiz-sale-200-125-exam    | What-is-the-difference-sale-200-125-exam-cert    | boson-practice-sale-200-125-exam-practice    | measureup-Cisco-Certified-Network-Associate-sale-200-125-exam    | globed-cisco-new-ccna-sale-200-125-exam-standard    | exam-labs-sale-200-125-exam-cert    | streaming-ccna-sale-200-125-exam-technologies    | caring-charts-blood-pressure-sale-200-125-exam    | pluralsight-courses-networking-cisco-sale-200-125-exam    | pearsonitcertification-articles-sale-200-125-exam    | safaribooksonline-library-sale-200-125-exam-routing    | learncisco-ccna.php-sale-200-125-exam-tast    | protechgurus-fees-syllabus-sale-200-125-exam    | certificationkits-cisco-ccna-sale-200-125-exam-standard-kit    | zeqr-lazaro-diaz-course-sale-200-125-exam    | 9tut-faqs-tips-sale-200-125-exam    | scribd-document-CCNA-sale-200-125-exam    | itunes-ccnax-sale-200-125-exam    | linkedin-cisco-sale-200-125-exam-questions-details    | teachertube-ccna-sale-200-125-exam-practice    | killexams-detail-sale-200-125-exam    | examsboost-test-sale-200-125-exam    | ccnav6-online-full-collections-sale-200-125-exam    | spiceworks-topic-sale-200-125-exam    | behance-gallery-sale-200-125-exam    | vceguide-share-experience-sale-200-125-exam    | techexams-forums-ccna-sale-200-125-exam    | free4arab-sale-200-125-exam    | openlearning-courses-sale-200-125-exam    | mindhub-Cisco-Certified-Network-sale-200-125-exam    | vceplus-ccna-exam-sale-200-125-exam    | examsforall-cisco-sale-200-125-exam    | how2pass-ccna-practice-tests-sale-200-125-exam    | simulationexams-details-ccna-sale-200-125-exam    | teksystems-sale-200-125-exam-routing-switching    | cram-flashcards-sale-200-125-exam    | pass4cert-cisco-new-ccna-sale-200-125-exam    | snatpedia-ccnaa-sale-200-125-exam    | cert4sure-free-download-sale-200-125-exam    | logicindia-ccnarouting-switching-sale-200-125-exam    | justcerts-practice-questions-sale-200-125-exam    | isc2-cissp-sale-CISSP-exam    | infosecinstitute-cissp-boot-camp-sale-CISSP-exam    | tomsitpro-security-certifications-sale-CISSP-125-exam    | infoworld-cissp-certification-sale-CISSP-exam    | welivesecurity.com-cissp-certified-sale-CISSP-exam    | searchsecurity-definition-sale-CISSP-exam    | simplilearn-cyber-security-training-sale-CISSP-exam    | arstechnica-security-sale-CISSP-exam    | cybrary-course-cissp-sale-CISSP-exam    | skillset-cissp-sale-CISSP-exam    | transcender-certprep-sale-CISSP-exam    | pearsonvue-sale-CISSP-exam-cert    | gocertify-isc2-issp-sale-CISSP-exam    | trainingcamp-training-bootcamp-sale-CISSP-exam    | cbtnuggets-security-sale-CISSP-exam    | cglobalknowledge.com-us-en-sale-CISSP-exam    | itgovernance-cissp-sale-CISSP-exam    | boson-certification-sale-CISSP-exam    | firebrandnordic-training-sale-CISSP-exam    | firebrandnordic-sale-CISSP-exam-123    | cybervista-sale-CISSP-exam-cert    | becker-sale-CISSP-exam-pdf    | youracclaim-certified-information-sale-CISSP-exam    | techexams-forums-sale-CISSP-exam    | munitechacademy-courses-sale-CISSP-exam    | hot-topics-cyber-security-courses-sale-CISSP-exam    | pearsonitcertification-sale-CISSP-exam    | sybextestbanks-wiley-sale-CISSP-exam    | lifewire-preparing-sale-CISSP-exam    | villanovau.com-resources-iss-sale-CISSP-exam    | intenseschool-boot-sale-CISSP-exam    | phoenixts-training-sale-CISSP-exam    | infosecisland-blogview-sale-CISSP-exam    | centralohioissa-member-sale-CISSP-exam    | learningtree-courses-certified-information-sale-CISSP-exam    | udallas.edu-executive-education-sale-CISSP-exam    | umbctraining-Courses-catalog-sale-CISSP-exam    | skyhighnetworks-cloud-security-sale-CISSP-exam    | helpnetsecurity-cert-sale-CISSP-exam    | secureninja-certification-bootcamp-sale-CISSP-exam    | mercurysolutions-information-sale-CISSP-exam    | exam-labs-info-sale-100-105-exam-pdf    | cbtnuggets-training-ccna-icnd1-sale-100-105-exam    | gocertify-ccent-practice-quiz-sale-100-105-exam    | ciscopress.com-ccna-icnd1-sale-100-105-exam    | boson-practice-sale-100-105-exam    | examcollectionuk-vce-download-sale-100-105-exam    | pearsonitcertification-articles-sale-100-105-exam    | transcender-practice-sale-100-105-exam-test    | techexams-forums-ccna-ccent-sale-100-105-exam    | shop-oreilly-sale-100-105-exam    | safaribooksonline-library-view-sale-100-105-exam    | subnetting-download-ccent-sale-100-105-exam    | 2cram-icnd1-online-quiz-sale-100-105-exam    | networklessons-routing-sale-100-105-exam    | centriq-123-ccna-certification-sale-100-105-exam    | ituonline-interconnecting-sale-100-105-exam    | transcender-introducing-the-new-sale-100-105-exam    | measureup-Networking-Devices-Part-sale-100-105-exam    | vceguide-icnd1-experience-sale-100-105-exam    | dumpscollection-dumps-sale-100-105-exam    | computerminds-business-sale-100-105-exam    | globed-ccent-or-icnd1-sale-100-105-exam    | ucertify-load-course-sale-100-105-exam    | academy-gns3-sale-100-105-exam    | visiontrainingsystems-product-sale-100-105-exam    | pearsonhighered-program-Wilkins-CCENT-sale-100-105-exam    | vceplus-ccent-sale-100-105-exam    | mindhub-Interconnecting-sale-100-105-exam    | sale-70-410-exam    | we-sale-70-410-exam    |
http://mleb.net/    | http://mleb.net/    |